MPN: SLA0101 / SLA0102
- Extra room for gloved hands
- Fills the gap in between the Mil-Spec trigger guard and the front of the pistol grip
- Tool-Less Model:
- Tool-less installation
- Spring loaded detents
- Built-in rubber bumpers eliminate any rattling
- Standard Model:
- Comes with a roll pin and a set screw
- Material: Billet Aluminum
- Finish: Mil-Spec Type III Hardcoat Anodizing
- Weight: 0.5 oz.
- AR-15 and AR-10
If you aim to build the perfect AR-15, it's important that every last part be made to the highest standards. This is the idea behind the Billet Trigger Guard Gen 2 from Spike's Tactical.
This Trigger Guard is machined out of solid billet aluminum, so you know it will be as tough as the rest of your AR-15. A downward curve makes the trigger more accessible when you are wearing winter or tactical gloves. You can be sure that your fingers won't be chafed during long range sessions by a rough texture or sloppy machining; the inside of the trigger guard is smooth as glass. The familiar Spike's Tactical spider logo will match your lower receiver as well.
Spikes Tactical Trigger Guard: Faster, More Intuitive Handling
Spikes Trigger Guard is designed with extra space to allow you to operate smoothly, even if your hands are larger than average, or circumstances require you wear gloves. That extra space will let you engage quicker when it counts, whether that’s on the competition range or out in the world.
The long bottom line of Spikes Trigger Guard not only gives you room to move, but it also makes the gap ahead of your pistol grip a thing of the past. No more catch point and an extended bottom line allow you to grasp your weapon the way you want and operate more fluidly.
Quality You Deserve
Spikes Tactical Trigger Guard is machined from Aircraft Grade 7075-T6 aluminum for strength without excess weight. The precision fit and finish of Spikes Trigger Guard make it an upgrade worth making. The Velvety Mil-spec Type III Hard-Anodized finish not only looks on point, but it’s as tougher than the environment you work in. It won’t chip, crack or let corrosion have its way.
The Look You Want
Just in case all that fine finishing is a little bit too smooth for you, Spikes gave their trigger guard a little attitude. The Generation 2 trigger guard features a faceted bottom line and Spike’s wicked Spider Logo that let them see a hint of the predator inside.
Install It Your Way
Choose the standard model and secure it with the included roll pin and set screw or the Tool-Less model with spring loaded detents and special rubber bumpers to stop rattles dead. Either way, you’ll get a secure installation that won’t let you down because Spikes gives you an edge however you roll.
Perfect fit, function, and easy install
Posted by Dern on 30th Aug 2018
Fit excellently and just one more thing that makes my custom build look and feel high quality, completely relieved the irritation of my second finger while holding my weighted rifle with one hand. Mil spec guard would cut into my finger after long sessions and this one is shaped perfectly to allow firing hand control of the rifle without discomfort.
I'd buy it again
Posted by Abs on 30th Jun 2017
This is my first after market trigger guard and it took a little while to pick it, but I think it's just right. I like the looks, it's not over-done, but it's not so modest it's invisible. It's just right. It also looks cool.
It's well machined and finished. The coating is really nice, and while it's a different shade and texture compared to my Aero Precision lower, it actually looks good on the receiver. I also really like that it has a screw-less installation, it was so easy to install and remove.
I will say that it was a bit loose when installed and was prone to a minor rattle as it shifted around in the receiver. It does come with a couple adhesive foam pads already installed intended to take-up the slack, but it's not enough in my installation. The noise is problematic in a defensive situation, and frankly it bugged the heck out of me.
Fortunately it was a simple solution, I applied a little Shoe Goo in the gap, and that made it all perfect. Now it's solid!
The reason I knocked a star off was partially for the slack problem, but mostly because they should have provided some extra pads to take up any potential slack that a customer may encounter. Maybe it's unique to my build, but Aero lowers are super popular, so I'm sure others will see the issue as well.
But small matter, I'll def buy this product again for my next build.
Posted by Unknown on 19th Jan 2016
Awesome trigger guard light weight & fit is great no movement at all plus very fast shipping
awesome trigger guard
Posted by Matt S on 17th Oct 2015
Looks great easy to install